[Dec-2016-New]Cisco 200-105 Exam PDF and VCE Free Download in Braindump2go[191-200]

2016/12 New Cisco 200-105: Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) Exam Questions Updated Today!
Free Instant Download 200-105 Exam Dumps (PDF & VCE) 346q from Braindump2go.com Today!

100% Real Exam Questions! 100% Exam Pass Guaranteed!

1.|2016/12 New 200-105 Exam Dumps (PDF & VCE) 346q Download:
2.|2016/12 New 200-105 Exam Questions & Answers:

Which command can be used from a PC to verify the connectivity between hosts that connect through a switch in the same LAN?

A.    ping address
B.    tracert address
C.    traceroute address
D.    arp address

Answer: A

When using the CLI, which banner displays a message upon every connection that is made into
the router?

A.    exec
B.    login
C.    motd
D.    slip-ppp

Answer: C

Which IPv6 address is the all-router multicast group?

A.    FF02::1
B.    FF02::2
C.    FF02::3
D.    FF02::4

Answer: B

Refer to the exhibit. What does STATUS=ACTIVE refer to in the output of the show frame-relay pvc command?

A.    The PVC is experiencing congestion.
B.    The Frame Relay switch is correctly programmed with the DLCI and is operational.
C.    The router is actively broadcasting to establish a link to the Frame Relay switch.
D.    The router is connected to the local Frame Relay switch, but not to the far end device.

Answer: B

The network administrator of the Oregon router adds the following command to the router configuration: ip route What are the results of adding this command? (Choose two.)

A.    The command establishes a static route.
B.    The command invokes a dynamic routing protocol for
C.    Traffic for network is forwarded to
D.    Traffic for all networks is forwarded to
E.    This route is automatically propagated throughout the entire network.
F.    Traffic for network is forwarded to the network.

Answer: AC

A network administrator would like to implement NAT in the network shown in the graphic to allow inside hosts to use a private addressing scheme. Where should NAT be configured?

A.    Corporate router
B.    Engineering router
C.    Sales router
D.    all routers
E.    all routers and switches

Answer: A

A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices. What would be the most efficient way to configure MAC-level security on all these ports?

A.    Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.
B.    Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.
C.    Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them.
D.    Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.

Answer: C

Which IPv6 address is the equivalent of the IPv4 interface loopback address

A.    ::1
B.    ::
C.    2000::/3
D.    0::/10

Answer: A

The network administrator is asked to configure 113 point-to-point links. Which IP addressing scheme best defines the address range and subnet mask that meet the requirement and waste the fewest subnet and host addresses?

A. subnetted with mask
B. subnetted with mask
C. subnetted with mask
D. subnetted with mask
E. subnetted with mask

Answer: D

Which address is the IPv6 all-RIP-routers multicast group address that is used by RIPng as the destination address for RIP updates?

A.    FF02::6
B.    FF02::9
C.    FF05::101
D.    FF02::A

Answer: B


1.|2016/12 New 200-105 Exam Dumps (PDF & VCE) 346q Download:
2.|2016/12 New 200-105 Study Guide:


Braindump2go Testking Pass4sure Actualtests Others
$99.99 $124.99 $125.99 $189 $29.99/$49.99
Real Questions
Error Correction
Printable PDF
Premium VCE
VCE Simulator
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back