[Dec-2016-New]100% Success-Braindump2go 200-105 Dump PDF 346q Instant Download[151-160]

2016/12 New Cisco 200-105: Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) Exam Questions Updated Today!
Free Instant Download 200-105 Exam Dumps (PDF & VCE) 346q from Braindump2go.com Today!

100% Real Exam Questions! 100% Exam Pass Guaranteed!

1.|2016/12 New 200-105 Exam Dumps (PDF & VCE) 346q Download:
http://www.braindump2go.com/200-105.html
2.|2016/12 New 200-105 Exam Questions & Answers:
https://1drv.ms/f/s!AvI7wzKf6QBjgR8N2yzsALYPi7P6

 

QUESTION 151
The network technician is planning to use the 255.255.255.224 subnet mask on the network. Which three valid IP addresses can the technician use for the hosts? (Choose three.)

A.    172.22.243.127
B.    172.22.243.190
C.    172.22.243.191
D.    192.168.1.160
E.    10.17.64.34
F.    10.16.33.98

Answer: BEF

QUESTION 152
Which of these represents an IPv6 link-local address?

A.    FE80::380e:611a:e14f:3d69
B.    FE81::280f:512b:e14f:3d69
C.    FEFE:0345:5f1b::e14d:3d69
D.    FE08::280e:611:a:f14f:3d69

Answer: A
Explanation:
Understanding IPv6 Link Local Address
Reference:
http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080ba1d07.shtml
The purpose of this document is to provide an understanding of IPv6 Link-local address in a network. A linklocal address is an IPv6 unicast address that can be automatically configured on any interface using the linklocal prefix FE80::/10 (1111 1110 10) and the interface identifier in the modified EUI-64 format. Link-local addresses are not necessarily bound to the MAC address (configured in a EUI-64 format). Link-local addresses can also be manually configured in the FE80::/10 format using the ipv6 address link-local command.

QUESTION 153
Refer to the graphic and routing table for router R1. Based on the output of the R1# show ip route command and the information presented in the graphic, which of the following is a potential routing problem?

A.    the use of summarization for discontiguous networks
B.    the use of CIDR with a routing protocol that does not support it
C.    the use of VLSM with a routing protocol that does not support it
D.    the use of the no auto-summary command with a protocol that does not support summarization
E.    the use of the ip route 0.0.0.0 0.0.0.0 command with a routing protocol that does not support it

Answer: A

QUESTION 154
What are three characteristics of the OSPF routing protocol? (Choose three.)

A.    It converges quickly.
B.    OSPF is a classful routing protocol.
C.    It uses cost to determine the best route.
D.    It uses the DUAL algorithm to determine the best route.
E.    OSPF routers send the complete routing table to all directly attached routers.
F.    OSPF routers discover neighbors before exchanging routing information.

Answer: ACF

QUESTION 155
An administrator is troubleshooting a problem between routers that are using different versions of RIP. Which two commands would provide information about which version of RIP was being sent and received on an interface? (Choose two.)

A.    show ip protocols
B.    show ip route rip
C.    show interfaces
D.    debug rip routing
E.    debug ip rip

Answer: AE

QUESTION 156
Refer to the exhibit. You are connected to the router as user Mike.
Which command allows you to see output from the OSPF debug command?
A.    terminal monitor
B.    show debugging
C.    show sessions
D.    show ip ospf interface

Answer: A

QUESTION 157
Refer to the exhibit. Host A has tested connectivity to a remote network. What is the default gateway for host A?
A.    10.16.176.1
B.    192.168.1.6
C.    192.168.1.1
D.    172.16.182.1

Answer: D

QUESTION 158
Refer to the exhibit. What is the result of setting the no login command?
A.    Both SSH and Telnet access is denied.
B.    Both SSH and Telnet access requires a password.
C.    Both SSH and Telnet access requires a new password at first login.
D.    There is a virtually limitless supply of IP addresses.

Answer: D

QUESTION 159
What does the “Inside Global” address represent in the configuration of NAT?

A.    the summarized address for all of the internal subnetted addresses
B.    the MAC address of the router used by inside hosts to connect to the Internet
C.    a globally unique, private IP address assigned to a host on the inside network
D.    a registered address that represents an inside host to an outside network

Answer: D

QUESTION 160
Refer to the graphic. A company wants to use NAT in the network shown. Which commands will apply the NAT configuration to the proper interfaces? (Choose two.)

A.    R1(config)# interface serial0/1
R1(config-if)# ip nat inside
B.    R1(config)# interface serial0/1
R1(config-if)# ip nat outside
C.    R1(config)# interface fastethernet0/0
R1(config-if)# ip nat inside
D.    R1(config)# interface fastethernet0/0
R1(config-if)# ip nat outside
E.    R1(config)# interface serial0/1
R1(config-if)# ip nat outside source pool 200.2.2.18 255.255.255.252
F.    R1(config)# interface fastethernet0/0
R1(config-if)# ip nat inside source 10.10.0.0 255.255.255.0

Answer: BC


!!!RECOMMEND!!!

1.|2016/12 New 200-105 Exam Dumps (PDF & VCE) 346q Download:
http://www.braindump2go.com/200-105.html
2.|2016/12 New 200-105 Study Guide:
https://youtu.be/MPVtnwlwW3E

         

Braindump2go Testking Pass4sure Actualtests Others
$99.99 $124.99 $125.99 $189 $29.99/$49.99
Up-to-Dated
Real Questions
Error Correction
Printable PDF
Premium VCE
VCE Simulator
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back